To replace a print cartridge:
When a print cartridge runs out of ink, leave the empty cartridge in the cradle until
you can replace it. The printer does not print with only one print cartridge in the
cradle.
1
- HP Deskjet 930cm Printer
- >
- Using and Caring for Your Print Cartridges
- >
- Replacing Print Cartridges
- >
- To replace a print cartridge:
HP Deskjet 930cm Printer - To replace a print cartridge:
HP Deskjet 930cm Printer > To replace a print cartridge:
- Table of Contents
- Introduction
- Printing Basics
- Using Your Printer Software
- Using and Caring for Your Print Cartridges
- Print Cartridge Status
- 1 Insert a print cartridge if it is missing.
- 2 Remove and reinsert the existing print cartridge.
- 3 If there is still a problem, verify that the cartridge is an HP C6578 Series, easy reference nu
- 4 If the problem persists, replace the cartridge.
- 1 Insert a print cartridge if it is missing.
- 2 Remove and reinsert the existing print cartridge.
- 3 If there is still a problem, verify that the cartridge is an HP 51645 Series, easy reference nu
- 4 If the problem persists, replace the cartridge.
- Replacing Print Cartridges
- To replace a print cartridge:
- Warning
- Warning
- 6 Push the print cartridge firmly, straight down into the print cartridge cradle.
- 7 Close the cradle latch. When the latch is fully closed, you will hear a click.
- 8 Load plain white paper in the IN tray.
- 9 Close the top cover, then a calibration page will print.
- 10 If the Print Cartridge Status Light continues to blink after you install the new print cartrid
- Storing Print Cartridges
- Cleaning Print Cartridges
- When Do You Need to Clean?
- If You See Missing Lines or Dots
- If You See Ink Streaks
- Manually Cleaning the Print Cartridges and Print Cartridge Cradle
- Warning
- 3 Remove the print cartridges and set them on a piece of paper with the ink nozzle plate facing up.
- 4 Dip a clean cotton swab into distilled water and squeeze any excess water from the swab.
- 5 Clean the face and edges of the print cartridge as shown. Do NOT wipe the nozzle plate.
- 6 Inspect the cartridge for fibers on the face and edges. If fibers are still present, repeat the
- 7 Repeat the cleaning process for the other print cartridge.
- 1 Using clean, moistened swabs, wipe the underside of each wall of the cradle.
- 2 Repeat until no ink residue is seen on a clean swab.
- 3 Reinsert the print cartridges, then close the printer’s top cover.
- 4 Load white paper into the IN tray.
- 5 Reinsert the electrical power cord into the back of the printer.
- 6 Print a test page. Double-click the HP Deskjet Utility, icon in the Utilities folder on your ha
- Damage Resulting from Refilling the Print Cartridges
- Print Cartridge Status
- Getting Help When Things Go Wrong
- Troubleshooting Tips
- The printer software won’t install, what’s wrong?
- 1 Reinsert the CD and try again. If this doesn’t solve your problem…
- 2 Try inserting a CD that you know works. If that CD doesn’t work, you may need to replace your C
- 3 If other CD’s work but the printer software CD doesn’t, you may have a damaged CD. You can down
- 4 If you don’t have Web access, contact HP Customer Care. See page49, to locate the phone number
- 1 Make sure your printer is on and all connections are secure.
- 2 Close any virus protection programs that are running on your computer.
- 3 Uninstall your printer software. Insert the printer software CD into your computer, select Unin
- 4 If you have been using Apple’s QuickDraw GX software, turn it off. Your HP Deskjet printer is n
- Why won’t it print? continued
- 1 Make sure the power is on.
- 2 Make sure that all cable connections are secure.
- 1 Pull the paper out of either the IN tray or the OUT tray.
- 2 Press the Resume Button on the front of the printer.
- 3 If you were printing labels, make sure a label did not become unglued from the label sheet whil
- 4 If the paper jam has cleared, print your document again.
- 5 If the paper jam hasn’t cleared, open the Rear Access Door by turning the knob (counter-clockwi
- 6 Pull the jammed paper out of the printer, then replace the Rear Access Door.
- 7 Print your document again.
- 1 Lower the Fold-Up tray, and pull out the IN tray.
- 2 Slide out both of the paper guides.
- 3 Load paper and print your document.
- 1 Insert the Rear Access Door and engage lock.
- 2 Print your document again.
- 1 Check the amount of RAM and processor speed in your computer.
- 2 Free up some space on the computer’s hard drive. Having less than 100 MB of free space on your
- 1 Lift the printer cover and check the Print Cartridge status icons to make sure you are not out
- 2 If you are out of ink, replace the print cartridge. See “Replacing Print Cartridges” on page 30.
- 3 Print your document again.
- 1 Save the fax in a graphic format, such as TIFF.
- 2 Place it in a word processing document and print it from there.
- What do the flashing lights mean?
- 1 Insert paper.
- 2 Press the Resume Button .
- 1 Pull the paper out of either the IN tray or the OUT tray.
- 2 Press the Resume Button on the front of the printer.
- 3 If you were printing labels, make sure a label did not become unglued from the label sheet whil
- 4 If the paper jam has cleared, print your document again.
- 5 If the paper jam hasn’t cleared, open the Rear Access Door by turning the knob (counter clockwi
- 6 Pull the jammed paper out of the printer, then replace the Rear Access Door.
- 7 Print your document again.
- 1 Follow the on-screen directions for how to insert the paper.
- 2 Press the Resume Button .
- 1 Press the Power Button to turn the printer off. Then press the Power Button again to turn the p
- 2 If that doesn’t solve the problem, press the Power Button to turn the printer off.
- 3 Unplug the printer.
- 4 Plug the printer back in.
- 5 Press the Power Button to turn the printer on.
- Is there a problem with your printout? continued
- 1 Make sure the media is correctly oriented in the IN tray.
- 2 Make sure the paper guides fit snugly against the media.
- 1 Check the print cartridges status. See “Print Cartridge Status” on page 28.
- 2 If the printer is running out of ink, replace the print cartridge. See “Replacing Print Cartrid
- 1 Choose Print from the File menu.
- 2 Choose Ink Controls from the General menu.
- 3 Use the sliders to adjust ink density and ink drying time.
- 1 Review the printing instructions on page15.
- 2 Make sure that the paper length guides are snug up against the photo paper.
- 1 Go to the Paper/Type Quality dialog box. See “Paper Type/Quality” on page10.
- 2 Select HP Photo Paper as the Paper Type.
- 3 Select Best as the Quality type.
- 4 Select High Res Photo from better print resolution.
- 5 Print your document.
- 1 Go to the Paper Type/Quality dialog box. See “Paper Type/Quality” on page10.
- 2 Select Best print quality.
- The printer software won’t install, what’s wrong?
- HP Customer Care
- Troubleshooting Tips
- Supplies and Accessories
- Setup Instructions
- Using a USB Connection
- 1 Plug in the electrical power cord
- 2 Load white paper
- 3 Insert the print cartridges
- 4 Connect the USB cable
- 5 Install the printer software
- a Insert the HP Printer Software CD into your CD-ROM drive.
- b Double-click the HP Deskjet 900 Series Installer icon.
- c Follow the on-screen instructions to complete the installation. Your computer will restart when
- d After your computer restarts, the HP Deskjet Utility (Select Printer) dialog box opens.
- Using a USB Connection
- Specifications
- Legal Information
- Index
HP Deskjet 930cm Printer
Powered by inkjetdoc.com